Step-by-step fix
Step 1: Make sure the aerator is the likely problem
- Turn on the faucet you want to fix and note whether the flow is weak only at that one spout.
- Check a nearby faucet or another fixture in the house. If water pressure is normal elsewhere, the problem is more likely at this faucet tip than in the whole plumbing system.
- Look at the end of the faucet spout for a threaded aerator. Many are visible from below, and some sit slightly recessed.
- If the faucet sprays unevenly, sputters, or has a noticeably reduced stream, a clogged or damaged aerator is a strong match for the symptom.
If it works: You have a single faucet with poor flow and the aerator is accessible at the spout.
If it doesn’t: If several fixtures have low pressure, troubleshoot the broader water pressure issue before replacing this part.
Stop if:- The faucet body is loose, cracked, or leaking from somewhere other than the spout tip.
- You cannot identify an aerator at the spout and the faucet appears to use a hidden or specialty insert you cannot safely remove.
Step 2: Set up the sink and remove the old aerator
- Close the sink drain or place a bowl in the basin so small parts cannot fall down the drain.
- Wrap a soft cloth around the aerator or use a rubber grip pad to protect the finish.
- Try turning the aerator counterclockwise by hand while facing the faucet tip.
- If it is stuck, use slip-joint pliers or an adjustable wrench over the protected surface and turn gently until it breaks free.
- Unscrew the aerator completely and keep any old washer, screen, or insert together so you can compare the stack-up with the replacement.
If it works: The old aerator is off the faucet and the faucet threads are exposed.
If it doesn’t: If mineral buildup is locking it in place, apply steady pressure instead of jerking the tool, then try again with better grip protection.
Stop if:- The faucet finish starts to crush, peel, or deform under the tool.
- The spout itself begins twisting instead of just the aerator.
Step 3: Match the replacement before installing it
- Compare the old aerator and the new water pressure aerator side by side.
- Check that the diameter matches and that the threads are the same type for your faucet.
- Make sure any washer or gasket included with the new part is present and seated the same way the old one was.
- If the old aerator had multiple pieces, follow the replacement's included orientation rather than forcing the old stack into the new body.
If it works: The new aerator matches the old one closely enough to thread on by hand.
If it doesn’t: Take the old aerator with you when shopping or compare measurements before opening another replacement.
Stop if:- The new aerator is clearly the wrong size or thread type and will not start straight by hand.
Step 4: Clean the faucet tip and install the new aerator
- Use the toothbrush and running water to clean grit, scale, or old debris from the faucet threads and the spout opening.
- Wipe the threads clean so the new aerator can seat evenly.
- Start the new aerator by hand and turn it clockwise. It should thread on smoothly without resistance or wobble.
- Tighten it hand-snug first. If needed, give it a very small final snug with pliers or a wrench over a cloth, but do not overtighten.
If it works: The new aerator is seated evenly and feels snug without cross-threading.
If it doesn’t: Back it off and restart by hand if it feels rough, crooked, or tight in the first turn.
Stop if:- The aerator will not thread on straight after repeated careful attempts, which usually means a mismatch or damaged faucet threads.
Step 5: Flush the faucet and check for leaks
- Turn the faucet on slowly, then bring it up to full flow.
- Let the water run for 30 to 60 seconds to flush out any loose debris behind the new aerator.
- Watch the stream. It should look fuller and more even than before.
- Check around the aerator where it meets the spout. If you see drips at the threads, turn the faucet off and snug the aerator slightly.
If it works: The faucet runs with a steady stream and no leaking around the aerator.
If it doesn’t: Remove the aerator and recheck the washer position and thread alignment if the stream is still weak or the connection drips.
Stop if:- Water leaks from the faucet body, handle, or under the sink, which points to a different repair.
Step 6: Confirm the repair holds in normal use
- Use the faucet several times over the next day the way you normally would.
- Check that the flow stays consistent at both low and full volume.
- Look again for drips around the aerator after the faucet has been turned on and off a few times.
- If the pressure drops again quickly, remove the aerator and inspect for fresh debris, which can point to sediment coming from the supply lines or plumbing upstream.
If it works: The faucet keeps normal flow in real use and the new aerator stays dry and secure.
If it doesn’t: If the new aerator clogs again right away or the faucet still has weak flow, the restriction is likely elsewhere in the faucet or water supply path.
Stop if:- You keep finding heavy grit, rust, or recurring debris, which can signal a larger plumbing issue that needs diagnosis.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
How do I know the aerator is causing low water pressure?
If one faucet has weak flow but other fixtures in the home seem normal, the aerator is a common cause. A clogged aerator often also causes an uneven or splashing stream.
Can I just clean the old aerator instead of replacing it?
Sometimes yes. If the threads and housing are in good shape, cleaning out scale and debris may restore flow. Replace it if it is damaged, badly corroded, or still restricted after cleaning.
Why won't the new aerator screw on?
The most common reasons are the wrong thread type, the wrong diameter, or cross-threading. It should start smoothly by hand. If it does not, stop and recheck the match.
Do I need to shut off the water to replace a faucet aerator?
Usually no. You are working at the faucet tip, so you can normally remove and replace the aerator with the faucet off. Just keep the drain closed so small parts are not lost.
What if the new aerator clogs again quickly?
That usually means debris is coming from somewhere upstream, such as mineral buildup, sediment in the lines, or faucet internals shedding material. The aerator may not be the root cause in that case.