Step-by-step fix
Step 1: Make sure the aerator is the right repair
- Check whether the low pressure is happening at just one sink faucet, not throughout the whole house.
- Run both hot and cold water at that faucet. If both sides are weak at the spout, the aerator is a likely restriction.
- Look at the faucet tip for uneven spray, sputtering, or visible mineral buildup around the screen.
- Put the sink stopper in place or set a small bowl in the sink so small parts do not disappear down the drain.
If it works: You have a single faucet with weak flow at the spout, and the aerator is the most likely cause.
If it doesn’t: If several fixtures in the house have low pressure, or only the hot side is weak, troubleshoot the broader water supply or faucet valve before replacing the aerator.
Stop if:- Water is leaking from under the sink, around the faucet body, or inside the cabinet.
- The faucet spout is cracked, loose, or badly corroded enough that turning the aerator could damage it.
Step 2: Remove the old aerator carefully
- Wrap a soft cloth around the aerator or use a rubber grip pad.
- Turn the aerator counterclockwise when looking up at the faucet tip.
- If it is stuck, use slip-joint pliers over the cloth and apply light, steady pressure instead of squeezing hard.
- Set the old aerator and any washers or inserts aside in the order they came out.
If it works: The old aerator is off and the faucet threads are exposed without damage to the finish.
If it doesn’t: If the aerator will not budge, soak the tip with vinegar on a rag for a while and try again with gentle pressure.
Stop if:- The faucet tip starts twisting with the aerator instead of the aerator loosening.
- The metal is deforming, cracking, or flaking apart as you try to remove it.
Step 3: Match the replacement before installing it
- Compare the new aerator to the old one for diameter, thread style, and overall shape.
- Check whether your faucet uses male or female threads and make sure the replacement matches.
- Move any required washer or gasket into the new aerator if the replacement did not include one.
- Hand-thread the new aerator onto the faucet to confirm it starts smoothly.
If it works: The new aerator matches the faucet and threads on by hand without cross-threading.
If it doesn’t: If the new part feels loose, will not start straight, or bottoms out oddly, stop and get the correct size and thread type.
Stop if:- The faucet threads are stripped, badly corroded, or damaged enough that a new aerator cannot seat properly.
Step 4: Clean the faucet tip and threads
- Use the toothbrush to scrub mineral buildup from the exposed faucet threads and the inside edge of the spout.
- Wipe away debris so the new aerator can seat flat.
- If scale is heavy, use a little vinegar on the brush or cloth and clean again.
- Rinse the area and wipe it dry.
If it works: The faucet tip is clean, and the new aerator has a smooth surface to seal against.
If it doesn’t: If buildup keeps breaking loose from inside the spout, flush the faucet briefly before final installation.
Stop if:- You find broken thread sections or deep corrosion that prevents a clean sealing surface.
Step 5: Install and snug the new aerator
- Thread the new aerator on by hand first to avoid cross-threading.
- Tighten it until it is snug and seated evenly against the faucet tip.
- If needed, use the cloth and pliers for a very small final snugging turn.
- Do not overtighten. The aerator only needs to be secure enough not to leak or loosen during use.
If it works: The new aerator is installed straight, snug, and the faucet finish is still protected.
If it doesn’t: If the aerator binds, backs off, or sits crooked, remove it and start the threads again by hand.
Stop if:- The aerator cannot be tightened without wobbling, or the faucet threads will not hold it securely.
Step 6: Test the faucet in real use
- Open the faucet slowly, then fully, and watch the stream pattern.
- Run both hot and cold water and check for stronger, steadier flow.
- Look at the aerator connection for drips while the water is running and again right after shutoff.
- Use the faucet normally for a day or two and make sure the improved flow holds during regular handwashing and sink use.
If it works: The faucet has a steady stream, better flow, and no leaking at the aerator after normal use.
If it doesn’t: If flow is still weak after replacing the aerator, the restriction may be deeper in the faucet, supply lines, or shutoff valve.
Stop if:- Water leaks around the spout connection and will not stop with proper snugging.
- The faucet still has poor flow on one side only, which points to a different repair path than the aerator.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
How do I know if the aerator is causing low water pressure?
If one faucet has weak flow while other fixtures in the home seem normal, the aerator is a common cause. Mineral buildup and debris often collect in the screen and restrict flow right at the spout.
Can I clean the old aerator instead of replacing it?
Sometimes, yes. If the screen is only clogged with mineral scale or debris, cleaning may restore flow. Replace it if the screen is damaged, the housing is corroded, or cleaning does not improve performance.
Why won't my new aerator fit?
Faucet aerators come in different diameters and thread types. The most common mistake is buying the wrong thread style or size. Match the old aerator carefully before ordering or installing.
Do I need to shut off the water to replace a faucet aerator?
Usually no. You are working at the faucet tip, not opening the water lines. Just make sure the faucet is off before you start.
What if the faucet still has low pressure after I replace the aerator?
The restriction may be inside the faucet, in the shutoff valve, or in the supply line. If only hot or only cold is weak, the problem is less likely to be the aerator alone.