Step-by-step fix
Step 1: Confirm the suspension rods are the likely problem
- Unplug the washer and open the lid.
- Press down on the inner tub by hand and let it rise back up.
- Look for a tub that sits noticeably low, leans to one side, or rebounds too loosely instead of settling under control.
- Think about the symptoms you have seen in real use: loud banging during spin, frequent out-of-balance stops, or the basket slamming the cabinet even with normal-sized loads.
- Rule out simple loading issues first by making sure the problem was not caused by one heavy item or a badly uneven load.
If it works: The tub support feels weak or uneven, and the symptoms match worn suspension rods.
If it doesn’t: If the tub feels stable and the problem only happens with oversized or single-item loads, correct the loading pattern before replacing parts.
Stop if:- You find a cracked tub, broken cabinet frame, damaged top support, or severe rust around the rod mounting points.
- The washer is leaking heavily into the cabinet or has obvious drive-system damage that points to a different repair.
Step 2: Set up the washer and open the top
- Turn off the water supply if you need to pull the washer forward for access.
- Move the washer out enough to work comfortably behind or beside it.
- Open the top the way your washer is designed: remove screws if present, or release the front clips with a putty knife and lift the top.
- Support the top securely so it cannot fall while your hands are inside the cabinet.
- Take a quick photo of the rod locations before removing anything.
If it works: You have safe access to all suspension rod mounting points.
If it doesn’t: If the top will not release, look again for hidden screws at the back or under trim pieces instead of forcing it.
Stop if:- The top hinge area or cabinet support is bent enough that the top will not stay open safely.
- You cannot access the rods without prying hard enough to risk damaging the cabinet.
Step 3: Remove the old suspension rod kit
- Support the tub with one hand so it does not drop or shift suddenly when a rod is released.
- Remove one old rod at a time by lifting it out of its upper mount and then freeing the lower end from the tub support.
- Pay attention to how the spring seat, bushing, or support cup is positioned on each rod.
- Repeat until all rods in the kit are removed.
- Compare the old parts to the new kit and make sure the lengths, ends, and support pieces match.
If it works: All old suspension rods are out, and the new kit matches the original setup closely enough to install.
If it doesn’t: If one rod looks different from the others, recheck your photo and the replacement packaging before installing anything.
Stop if:- A rod mount is cracked, torn loose, or rusted through.
- The replacement kit does not match the original rod length or end style well enough to install safely.
Step 4: Install the new suspension rods
- Install the new rods one at a time so the tub stays supported and you do not lose track of the layout.
- Seat the lower end of each rod into the tub support the same way the old one sat.
- Guide the upper end into its cabinet mount and make sure any spring seat or bushing is fully seated.
- Repeat for the remaining rods until the tub is evenly suspended on the full new kit.
- Check that the tub now hangs centered and does not rub the cabinet opening.
If it works: The new suspension rod kit is fully installed, and the tub sits centered with even support.
If it doesn’t: If the tub still leans, one rod may not be seated correctly in its upper or lower mount. Recheck each corner.
Stop if:- Any rod will not seat fully in its mount or pops back out under normal tub weight.
- The tub support bracket is bent enough that the new rods cannot hold the basket evenly.
Step 5: Reassemble the washer and do a controlled test
- Lower the top carefully and reinstall any screws or clips you removed.
- Move the washer back into place without crushing the drain hose or water lines.
- Reconnect power and turn the water back on if you shut it off.
- Run a short rinse and spin cycle with the basket empty first.
- Listen for scraping, hard knocking, or a tub that still swings excessively.
If it works: The washer runs through an empty spin more smoothly, with less banging and better tub control.
If it doesn’t: If the washer still shakes badly while empty, re-open the top and confirm every rod is installed in the correct position and fully seated.
Stop if:- You hear metal-on-metal impact, see the tub striking the cabinet, or notice a new leak after reassembly.
Step 6: Verify the repair with a real laundry load
- Wash a normal mixed load, not a single heavy item like one rug or one soaked blanket.
- Watch the washer during the transition into spin and listen for the original banging noise.
- Check that the basket stays more centered and that the machine reaches full spin without repeated balance interruptions.
- After the cycle, confirm the cabinet has not walked forward and the tub still sits level when empty.
If it works: The washer handles a normal load without the old banging, violent shaking, or repeated out-of-balance behavior.
If it doesn’t: If the symptoms improved only slightly, level the washer on the floor and inspect for other worn support or drive parts that can also cause shaking.
Stop if:- The washer still slams the cabinet with normal loads, which points to another fault beyond the suspension rod kit.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
Do I need to replace all the suspension rods or just one?
Replace the full kit. Mixing old and new rods usually leaves the tub uneven and can bring the shaking back quickly.
What symptoms point to bad suspension rods?
Common signs are loud banging in spin, frequent out-of-balance stops, a tub that sits low or leans, and a basket that swings too freely by hand.
Can bad suspension rods make the washer walk across the floor?
Yes. If the tub is not controlled well during spin, the washer can shake hard enough to move. Make sure the floor is solid and the washer is level too.
Is this the same as replacing shock absorbers?
Not exactly. Some washers use suspension rods, while others use shocks or a different support system. Match the replacement part to your exact washer design.
Why does the washer still shake a little after the repair?
Some movement is normal, especially as the load redistributes before full spin. If the machine still bangs hard or stops for balance with normal loads, check leveling and look for another worn support part.