Step-by-step fix
Step 1: Make sure the leak is really coming from the slip-joint washers
- Dry the trap, nuts, and nearby pipes with a towel.
- Run a small amount of water, then watch each slip-joint connection closely.
- Look for water forming right at the nut where two trap pieces join.
- Check the trap body and tailpiece for cracks, splits, or badly corroded metal.
If it works: You confirmed the leak is coming from a slip-joint connection and not from a cracked pipe or a different fitting.
If it doesn’t: If the leak starts higher up at the sink basket, dishwasher branch, or wall connection, fix that connection instead of replacing the washer set.
Stop if:- The trap body or connected pipe is cracked, badly rusted through, or deformed.
- The leak is coming from inside the wall or from a glued connection rather than a slip-joint nut.
Step 2: Set up the area and remove the trap
- Place a bucket or shallow pan directly under the P-trap.
- Empty out stored items under the sink so you have room to work.
- Loosen the slip-joint nuts by hand first. Use pliers only if needed.
- Support the trap as you remove the last nut so it does not drop and spill dirty water.
- Pour the trapped water into the bucket and set the trap pieces on a towel.
If it works: The trap is off and you can access the old washers and mating surfaces.
If it doesn’t: If a nut is frozen, try a rag for better grip and use pliers gently so you do not crush the plastic nut.
Stop if:- A pipe inside the wall moves loosely, pulls outward, or shows signs of hidden damage when you loosen the trap.
- A plastic nut or pipe starts cracking while you are trying to remove it.
Step 3: Remove the old washers and clean the joint surfaces
- Slide the old slip-joint nuts and washers off the pipe ends.
- Compare the old washers to the new set so you can match the size and shape.
- Wipe the pipe ends, trap openings, and nut threads clean.
- Use a small nylon brush to remove grime, old residue, and buildup from the sealing areas.
- Inspect the pipe ends for gouges, out-of-round sections, or deep wear where the washer seats.
If it works: The joint surfaces are clean and ready for the new washers to seat evenly.
If it doesn’t: If the new washers do not match the old size or the pipe diameter, pause and get the correct set before reassembling.
Stop if:- The pipe end is split, badly warped, or too damaged for a new washer to seal.
- The trap alignment is so far off that the pipes have to be forced together to meet.
Step 4: Install the new slip-joint washers in the correct direction
- Slide the slip-joint nut onto the pipe first, with the threads facing the joint.
- Slide the new washer on next, with the narrower side facing into the fitting and the wider side toward the nut.
- Seat the pipe fully into the trap connection before threading the nut on.
- Start each nut by hand to avoid cross-threading.
- Reassemble the full trap so the pieces line up naturally without side pressure.
If it works: The new washers are in place and the trap is reassembled with the joints aligned correctly.
If it doesn’t: If a nut will not thread smoothly by hand, back it off and realign the pipe and washer before trying again.
Stop if:- You have to bend or force the drain pipes to make the trap fit.
- The washer keeps slipping out of place because the wrong size or style is being used.
Step 5: Tighten the joints and check for immediate leaks
- Hand-tighten each slip-joint nut until snug.
- If needed, give each nut a small additional turn with pliers, using light pressure only.
- Wipe every joint dry so fresh drips are easy to spot.
- Run water slowly for 30 seconds, then a little faster while watching each connection with a flashlight.
- Touch around the nuts and underside of the joints with a dry finger or paper towel to catch tiny leaks.
If it works: The trap holds under a basic water test with no fresh drips at the slip-joint connections.
If it doesn’t: If a joint drips, tighten that nut slightly. If it still leaks, take it back apart and check washer direction, fit, and pipe alignment.
Stop if:- A nut cracks or the trap body distorts while tightening.
- Water is leaking from a crack in the pipe rather than from the washered joint.
Step 6: Verify the repair under normal sink use
- Fill the sink partway and release the water to send a stronger flow through the trap.
- If you have a two-bowl sink, run water through both sides one at a time if they drain through the same trap setup.
- Check again for drips over the next several minutes, especially at the joints you disturbed.
- Wipe the area dry and leave a dry paper towel under the trap for a short follow-up check.
If it works: The trap stays dry during a full drain cycle and remains dry afterward, confirming the washer replacement fixed the leak.
If it doesn’t: If the paper towel shows moisture later, recheck the exact joint location. A misaligned washer, overtightened nut, or worn trap piece may still need attention.
Stop if:- Leaks continue after reinstalling the washers correctly and lightly retightening the joints.
- You find recurring movement, hidden cabinet damage, or signs that the drain assembly is failing beyond the washer set.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
Do I need to replace the whole P-trap or just the washers?
If the leak is only at the slip-joint nuts and the trap pieces are not cracked or badly worn, replacing the washers is often enough. If the trap body is damaged or the pipes no longer line up well, replacing the full trap assembly is usually the better fix.
Which way does a slip-joint washer face?
The narrower side usually faces into the fitting, and the wider side faces the nut. That lets the washer wedge into the joint as the nut tightens.
Should I use plumber's putty or tape on slip-joint washers?
No. Slip-joint washers are meant to seal by compression. Tape and putty usually do not help here and can make the joint harder to seat correctly.
How tight should the slip-joint nuts be?
Start with hand-tight. If a joint still drips, add only a small extra turn with pliers. Overtightening can crack plastic nuts or distort the washer.
Why does the trap still leak after I installed new washers?
The most common causes are the wrong washer size, the washer facing the wrong direction, dirty sealing surfaces, cross-threaded nuts, or pipes that are out of alignment. A cracked trap or worn pipe end can also keep a new washer from sealing.