Step-by-step fix
Step 1: Make sure filter replacement is the right fix
- Look for signs of restricted airflow such as stale indoor air, weaker exhaust or fresh-air flow, more frost buildup than usual, or visibly dirty filters.
- Turn the HRV off at its wall control or service switch before opening the cabinet.
- Open the access panel and inspect the filters. If they are packed with dust, discolored through most of the surface, torn, wet, or misshapen, replacement is the right next step.
- Check the inside of the cabinet for standing water, heavy ice, burnt wiring smell, or damaged plastic parts while you have it open.
If it works: The filters are clearly dirty, damaged, or overdue, and the cabinet looks safe enough for a normal filter change.
If it doesn’t: If the filters still look clean and airflow problems continue, the issue may be elsewhere, such as the core, drain, fan, or ducting.
Stop if:- You find standing water, heavy ice that blocks access, scorched wiring, or obvious internal damage.
- The unit will not shut off safely before you open it.
Step 2: Remove the old filters and note how they fit
- Slide or lift the old filters out carefully so built-up dust does not spill deeper into the unit.
- Pay attention to how each filter sits in its track and whether there is an airflow arrow or marked side.
- Compare the old filters to the new ones before installing anything. Check length, width, thickness, and overall shape.
- If one filter is more clogged than the other, note it. Uneven dirt loading can point to an airflow imbalance, but you can still complete the filter replacement.
If it works: The old filters are out, and you know the correct orientation and fit for the replacements.
If it doesn’t: If the new filters do not match the old ones closely, pause and get the correct size and thickness before continuing.
Stop if:- The filter frame or track is broken badly enough that the new filters will not stay seated.
- You discover the old filters were forced in and the replacement cannot fit without bending or trimming.
Step 3: Clean the filter compartment before installing new filters
- Use a vacuum with a brush attachment to remove loose dust from the filter compartment, tracks, and nearby cabinet surfaces.
- Use a soft brush to loosen dust in corners, then vacuum it up.
- Wipe the filter tracks and the access panel sealing surface with a dry or slightly damp microfiber cloth.
- If the old filters were damp, let the compartment dry fully before installing the new ones.
If it works: The filter area is clean, dry, and ready for the new filters to seal properly.
If it doesn’t: If dust keeps falling from deeper inside the unit, clean what you can reach safely and move on without forcing tools into the fan or core area.
Stop if:- You find mold-like growth, persistent water inside the cabinet, or corrosion that suggests a drainage or condensation problem.
- Cleaning exposes damaged wiring insulation or loose internal components.
Step 4: Install the new HRV filters in the correct direction
- Insert the new filters into the tracks the same way the old ones were installed.
- If the filters have airflow arrows, point them in the same direction as the originals or as marked inside the unit.
- Make sure each filter sits flat, fills the opening, and is not folded, bowed, or pinched by the frame.
- Reinstall any retaining clips or supports that hold the filters in place.
If it works: Both new filters are fully seated, aligned, and not leaving obvious gaps around the edges.
If it doesn’t: If a filter keeps popping out or leaves a gap, remove it and recheck the size, thickness, and orientation.
Stop if:- The access panel cannot close because the filters are too thick or incorrectly sized.
- The filter rack is too damaged to hold the filters securely.
Step 5: Close the unit and restart it
- Close and latch the access panel securely so the cabinet can seal properly.
- Turn the HRV back on at the control or service switch.
- If your unit has a filter reminder, reset it according to the label or owner instructions available for your unit.
- Listen for normal fan operation after startup.
If it works: The unit restarts normally with the panel closed and no unusual rattling, scraping, or air leaks around the door.
If it doesn’t: If the unit does not restart, recheck that the panel is fully closed and any door safety switch is engaged.
Stop if:- The unit trips a breaker, makes grinding noises, or gives off a burning smell after restart.
Step 6: Verify the repair under normal use
- Let the HRV run for several minutes, then check for steadier airflow at nearby supply and exhaust grilles.
- Confirm the access panel stays closed tightly and that no filter has shifted out of place.
- Over the next day or two, watch for improved ventilation and reduced signs of airflow restriction.
- Write down the replacement date so you can check the filters again on a regular schedule based on how dusty your home is.
If it works: Airflow is back to normal, the cabinet stays sealed, and the new filters remain seated during real operation.
If it doesn’t: If airflow is still weak after replacing the filters, the next checks are usually the heat-recovery core, drain condition, fan operation, and duct restrictions.
Stop if:- The unit continues icing up quickly, leaking water, or showing severe airflow problems after the filter change.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
How often should HRV filters be replaced?
It depends on dust levels, pets, renovation debris, and how often the unit runs. Many homeowners inspect them every few months and replace them when they are loaded with dust, damaged, or no longer cleaning up well.
Can I clean HRV filters instead of replacing them?
Some filters can be vacuumed or washed, but many disposable filters should be replaced. If the filter media is torn, collapsed, heavily embedded with dust, or stays dirty after cleaning, replacement is the better fix.
What happens if I install the filters backward?
Airflow can be reduced and the filters may not work as intended. If your filters have airflow arrows, install them in the correct direction before running the unit normally.
Why is one HRV filter dirtier than the other?
That can happen when supply and exhaust airflow are not perfectly balanced or one air stream carries more dust. Replacing the filters is still worthwhile, but uneven loading can be a clue to check airflow balance later if performance stays off.
Do I need to replace both HRV filters at the same time?
Usually yes. Replacing both together helps keep airflow more even and gives you a clear maintenance starting point.