Step-by-step fix
Step 1: Confirm the overload protector is a reasonable repair to try
- Make sure the freezer is plugged in and the outlet has power.
- Listen near the back of the freezer for a repeated click, a brief hum, or a compressor that tries to start and then stops.
- Check whether the interior light or control panel still works even though the freezer is not cooling.
- Pull the freezer away from the wall enough to reach the lower rear panel and look for obvious signs of overheating near the compressor area, such as melted plastic, burnt wiring, or a strong burnt smell.
If it works: The symptoms point to a compressor start problem, and the overload protector is a plausible failed part.
If it doesn’t: If the freezer is completely dead, the outlet has no power, or the problem is clearly elsewhere, diagnose the power supply, thermostat, control, or start components before replacing the overload protector.
Stop if:- You find burnt wires, melted connectors, or a damaged compressor terminal cover.
- The compressor shell is leaking oil or looks physically damaged.
- You are not comfortable working around appliance wiring and compressor components.
Step 2: Unplug the freezer and open the compressor area
- Unplug the freezer from the wall outlet.
- Move the freezer carefully so you can work behind it without straining the cord or water line if one is present.
- Remove the lower rear access panel with a nut driver or screwdriver.
- Locate the compressor. It is the black metal can near the bottom rear of the freezer.
- Find the overload protector attached at the compressor terminal area, usually under a small cover or clipped beside the start device.
If it works: The freezer is disconnected from power and you have clear access to the overload protector.
If it doesn’t: If you cannot identify the compressor terminal area, look for the wire-connected start components mounted directly on the side of the compressor.
Stop if:- The access panel or surrounding metal is badly rusted through or unsafe to handle.
- You cannot unplug the freezer safely or the outlet area is wet.
Step 3: Document the wiring and remove the old overload protector
- Take a clear photo of the wiring and part position before disconnecting anything.
- Remove any terminal cover, retaining clip, or bracket that holds the start components in place.
- Pull wire connectors off the overload protector by gripping the connector, not the wire itself.
- Slide or pull the overload protector off the compressor terminal assembly in the same direction it was installed.
- Inspect the old part for heat damage, cracking, or rattling pieces inside.
If it works: The old overload protector is out, and you have a clear reference for reinstalling the new one.
If it doesn’t: If the part feels stuck, wiggle it gently and check again for a hidden clip or cover instead of forcing it.
Stop if:- A wire connector breaks, a compressor terminal is loose, or the terminal area is charred.
- The replacement part does not match the old part's connector layout or mounting style.
Step 4: Install the new overload protector in the same position
- Compare the new overload protector to the old one and confirm the terminals, shape, and mounting style match.
- Push the new overload protector onto the compressor terminal assembly or into its holder exactly as the old one sat.
- Reconnect the wires to the same terminals shown in your photo.
- Reinstall any retaining clip, bracket, or terminal cover you removed.
- Check that all connectors are snug and that no wire is rubbing against the compressor or sharp metal edges.
If it works: The new overload protector is fully seated, wired correctly, and secured in place.
If it doesn’t: If the new part will not seat properly, remove it and recheck orientation and fit before applying pressure.
Stop if:- The new part fits loosely, the terminals do not align, or the wiring no longer reaches naturally.
- You discover damaged insulation or brittle wiring that needs repair before power is restored.
Step 5: Reassemble the rear panel and restore power
- Reinstall the lower rear access panel so airflow around the compressor is restored the way the freezer was designed.
- Move the freezer back carefully, leaving enough space so the cord is not pinched.
- Plug the freezer back in.
- Set the temperature control to a normal cooling setting if it was changed during troubleshooting.
- Listen for the compressor to start within the next several minutes.
If it works: The freezer is back together and powered on with the new overload protector installed.
If it doesn’t: If the compressor does not start right away, give it a few minutes. Some systems have a short delay before restarting.
Stop if:- The freezer trips the breaker, sparks, or gives off a burning smell after power is restored.
Step 6: Verify the repair holds during real operation
- Listen for a steady compressor run instead of repeated clicking on and off.
- After 15 to 30 minutes, check for signs of cooling returning inside the freezer.
- After several hours, confirm the freezer temperature is dropping normally and the compressor is cycling in a normal pattern instead of short-cycling.
- Keep an eye on the area behind the freezer for unusual heat, smell, or repeated restart attempts.
If it works: The compressor starts and runs normally, and the freezer begins cooling again without repeated clicking.
If it doesn’t: If the new overload protector does not solve the problem, the issue may be the start relay, capacitor if equipped, compressor windings, or another electrical fault that needs further diagnosis.
Stop if:- The compressor still clicks and shuts off repeatedly after the new part is installed.
- The compressor becomes extremely hot quickly or hums loudly without starting.
- Cooling does not return after several hours even though the compressor behavior still seems abnormal.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
What does a freezer compressor overload protector do?
It protects the compressor from overheating and excessive current draw. If the compressor struggles to start or overheats, the overload protector opens the circuit to prevent damage.
What symptoms point to a bad overload protector?
Common signs are a freezer that has power but does not cool, repeated clicking from the compressor area, or a compressor that hums briefly and shuts off. These symptoms can also overlap with a bad start relay or a failing compressor.
Can I replace just the overload protector without replacing other start parts?
Yes, if you have confirmed the overload protector is the failed part and the replacement matches your freezer. In some designs, the overload protector works alongside a start relay, so both parts may need inspection if the problem continues.
How do I know I ordered the right overload protector?
Match the replacement to your exact freezer model and compare the connector layout and mounting style to the original part before installing it.
What if the freezer still will not start after I replace the overload protector?
The problem may be a bad start relay, another wiring issue, or a compressor that is failing mechanically or electrically. At that point, more testing is needed before replacing more parts.