Step-by-step fix
Step 1: Confirm the drum glide is the likely problem
- Unplug the dryer before touching any panels.
- Open the door and look at the front edge of the drum and the area it rides against.
- Turn the drum by hand. Listen and feel for scraping, rough spots, or a front-edge drag.
- Look for signs of glide wear such as missing felt or plastic strips, exposed support material, black dust, or scoring on the drum lip.
- If the noise seems to come from the rear of the drum or from the blower or motor area, pause and recheck the diagnosis before ordering parts.
If it works: The symptoms point to a worn front drum glide and the repair path makes sense.
If it doesn’t: If the drum feels rough at the rear or the noise is deeper in the cabinet, inspect the rear support rollers, idler pulley, and blower area instead.
Stop if:- You smell burning insulation, see damaged wiring, or find signs of overheating inside the cabinet.
- The drum support area is cracked, bent, or badly worn beyond the glide itself.
Step 2: Open the dryer and remove the drum
- Pull the dryer forward enough to work comfortably and disconnect the vent if needed for access.
- Remove the lint screen if it sits in the top panel, then remove any screws that secure the top or front panel.
- Use a putty knife to release top clips if your dryer uses clips instead of screws.
- Lift the top and remove the front panel or front bulkhead carefully, watching for door switch wires.
- Take a quick photo of the belt routing before removing tension from the belt.
- Release belt tension at the idler pulley, slip the belt off the motor pulley, and lift the drum out of the cabinet.
If it works: The drum is out and you can clearly reach the front support area where the glide mounts.
If it doesn’t: If the drum will not lift out, check again for hidden screws, attached wires, or belt tension still holding it in place.
Stop if:- You have to force a panel that should be releasing normally.
- A wire connector, panel tab, or drum support is breaking instead of coming apart cleanly.
Step 3: Remove the worn glide and clean the support
- Locate the old glide on the front drum support or front bulkhead where the drum rides.
- Remove any clips, screws, or retainers holding the glide in place, and slide or peel the worn glide out.
- Compare the old part to the new one so the shape, length, and mounting style match.
- Vacuum lint from the support area and wipe away dust so the new glide sits flat.
- Inspect the support surface for grooves, sharp burrs, or heat damage that could ruin the new part quickly.
If it works: The old glide is removed and the mounting surface is clean and ready for the replacement.
If it doesn’t: If the new glide does not match the old one closely, stop and verify the dryer model before installing anything.
Stop if:- The front support is cracked, badly warped, or worn through where the glide mounts.
- The drum edge is deeply gouged or damaged enough to cut into a new glide.
Step 4: Install the new dryer drum glide
- Set the new glide into the support in the same direction and position as the original.
- Reinstall any clips, screws, or retainers so the glide is fully seated and cannot shift.
- Run your fingers along the glide path to make sure it sits evenly without twists or lifted edges.
- If your dryer uses more than one glide piece at the front support, replace the full worn set so the drum rides evenly.
- Wipe the front edge of the drum clean before putting it back in place.
If it works: The new glide is secure, aligned, and ready to support the drum smoothly.
If it doesn’t: If the glide rocks, slips, or will not seat fully, remove it and check for debris, a bent retainer, or the wrong replacement part.
Stop if:- The retainer will not hold the glide securely.
- The replacement part only fits by trimming, bending, or forcing it.
Step 5: Reinstall the drum and reassemble the dryer
- Set the drum back into the cabinet and rest its front edge on the new glide support.
- Loop the belt around the drum in its original position and route it back around the motor pulley and idler pulley.
- Turn the drum by hand several full rotations to make sure the belt tracks correctly and the drum rides smoothly on the new glide.
- Reconnect any door switch wires and reinstall the front panel or bulkhead.
- Lower the top, reinstall screws, reconnect the vent, and move the dryer back into place without crushing the vent hose.
If it works: The dryer is reassembled and the drum turns by hand without scraping or binding.
If it doesn’t: If the drum binds or the belt walks out of place, reopen the cabinet and correct the drum position or belt routing before running the dryer.
Stop if:- The drum will not rotate freely by hand after reassembly.
- You cannot restore the belt routing with confidence.
Step 6: Test the repair under real use
- Plug the dryer back in and run it empty for a few minutes on a normal heated cycle or air cycle.
- Listen for scraping, grinding, or repeated thumping from the front of the drum.
- Check that the drum starts promptly, turns steadily, and does not sag at the front when loaded with a few towels.
- After the short test, open the door and look for fresh black dust or signs the drum is rubbing where it should not.
If it works: The dryer runs smoothly, the front-edge noise is gone or greatly reduced, and the drum stays properly supported during use.
If it doesn’t: If the noise remains, inspect the rear rollers, idler pulley, drum felt seal, and blower wheel for a second worn part causing the same symptom.
Stop if:- The dryer still makes a harsh metal-on-metal sound.
- The drum rubs hard enough to leave fresh scoring, dust, or a burning smell during the test.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
What does a bad dryer drum glide sound like?
It often sounds like scraping, grinding, or a light metal-on-metal rub from the front of the dryer. Some dryers also make a rhythmic thump if the drum is no longer riding evenly.
Can I keep using the dryer with a worn drum glide?
It is better to stop using it until you fix it. A worn glide can let the drum rub the support, damage the drum edge, wear other parts faster, and create more noise and dust.
Should I replace more than one glide at the same time?
Yes, if your dryer uses multiple front glide pieces, replace the full worn set. Mixing a new glide with a badly worn one can leave the drum unevenly supported.
Do I need adhesive to install a dryer drum glide?
Not usually. Many glides are held by clips, retainers, or screws. Use only the mounting method your dryer is designed for and avoid improvising with glue unless the correct part setup specifically calls for it.
What if the dryer still makes noise after I replace the glide?
The glide may not have been the only worn part. Rear drum rollers, the idler pulley, drum seals, or the blower wheel can make similar noises, so inspect those next.