Step-by-step fix
Step 1: Confirm the P-trap washers are the likely problem
- Dry the entire trap, trap arm, and the bottom of the sink drain with a rag.
- Run a small amount of water, then watch each slip-joint nut on the P-trap.
- Look for dripping or moisture forming right at a trap connection where a washer sits.
- Check that the leak is not starting higher up at the sink drain body, faucet supply lines, or shutoff valves.
If it works: You have confirmed the leak is coming from a P-trap slip-joint connection and washer replacement is the right next step.
If it doesn’t: If the leak starts above the trap, fix the higher leak first because water can run down and make the trap look like the problem.
Stop if:- The drain pipe is cracked, badly corroded, or split.
- The wall stub-out is loose in the wall or damaged.
- The leak is coming from the sink drain flange or another part, not the trap connection.
Step 2: Set up the area and take the trap apart
- Place a bucket or bowl directly under the P-trap.
- Put down a rag under the bucket if the vanity floor is finished wood or particleboard.
- Loosen the slip nuts at the leaking connection and the opposite side of the trap. Start by hand, then use pliers only if needed.
- Lower the trap carefully and let the trapped water drain into the bucket.
- Slide the nuts back and remove the old washers from the joint or from the pipe ends.
If it works: The trap is off or loose enough to access both old washers and the water is contained.
If it doesn’t: If a nut will not move, wipe it dry and try again with pliers using light pressure so you do not crack a plastic nut.
Stop if:- A plastic nut starts to split or the trap breaks while loosening.
- The pipe alignment is so far off that the trap has been forced into place.
Step 3: Match the new washers and clean the sealing surfaces
- Compare the old washers to the new ones for diameter and overall shape.
- Clean the trap ends, trap arm, and the inside faces of the nuts so no grit or old residue is left behind.
- Inspect the pipe ends for cracks, deep gouges, or out-of-round damage that could keep a new washer from sealing.
- Set the new washers in the same locations as the old ones were removed from.
If it works: You have clean pipe ends and new washers that match the old ones closely enough to seat properly.
If it doesn’t: If the new washers do not match the old size or the nut will not slide over them correctly, pause and get the correct trap washer size or a matching trap kit.
Stop if:- The pipe end is cracked, misshapen, or too damaged for a washer to seal.
- The replacement washers are clearly the wrong size or style for the trap.
Step 4: Install the new washers and reassemble the trap
- Slide each slip nut onto the pipe first if it came off during disassembly.
- Position each new washer so it seats squarely at the joint and is not twisted or cocked to one side.
- Bring the trap back into place and start both slip nuts by hand to avoid cross-threading.
- Tighten the nuts evenly by hand until the joints feel snug and the trap sits naturally without strain.
- If needed, give each nut a small additional turn with pliers or a wrench. Do not overtighten, especially on plastic parts.
If it works: The trap is reassembled, aligned naturally, and the washers are compressed evenly at both joints.
If it doesn’t: If the trap will not line up without forcing it, loosen the nuts, reposition the trap, and try again before tightening.
Stop if:- The threads will not start cleanly and appear cross-threaded.
- The trap only fits when bent or forced sideways.
Step 5: Test for leaks with a small flow first
- Wipe every joint completely dry so fresh drips are easy to spot.
- Run cold water at a slow stream for 30 seconds while watching the repaired joints.
- Touch around each slip nut with a dry finger or paper towel to check for moisture.
- If you see a slight seep, tighten that nut just a little more and test again.
If it works: The repaired joints stay dry during a slow-flow test.
If it doesn’t: If the same joint still seeps after a careful minor tightening, take it back apart and check washer orientation, fit, and pipe alignment.
Stop if:- Water is leaking from a crack in the trap or drain pipe rather than the joint.
- A nut keeps spinning without tightening, suggesting damaged threads.
Step 6: Verify the repair holds during normal sink use
- Fill the sink partway, then release the stopper so a larger volume of water runs through the trap.
- Run both cold and hot water for a minute and check the joints again with a dry towel.
- Look at the vanity floor and the back side of the trap for any delayed drips.
- Check again after the next few normal uses to make sure the washers stayed sealed.
If it works: The trap stays dry during a full drain and normal use, confirming the washer replacement held.
If it doesn’t: If leaking returns after real use, replace the full trap assembly or inspect the sink drain connection above for a second leak source.
Stop if:- You find hidden water damage, swelling cabinet material, or signs of a long-term leak inside the vanity.
Replacement Parts
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
Do I need to replace both P-trap washers or just the leaking one?
If you already have the trap apart, replacing both washers is usually worth it. The second washer is often the same age and may start leaking soon after the first one.
Can I use plumber's putty or tape on P-trap washers?
Most slip-joint trap connections seal with the washer itself, not with thread sealant. In most cases, a clean, correctly sized washer and proper alignment are what stop the leak.
Why does the trap still leak after I installed new washers?
The most common causes are the wrong washer size, a washer installed crooked, cross-threaded nuts, overtightening that distorts the joint, or a cracked trap or drain pipe.
Should the slip nuts be hand-tight or wrench-tight?
Start with hand-tight, then add only a small extra turn if needed. Too much force can crack plastic nuts or deform the washer enough to create a leak.
Is it better to buy washers only or a full trap kit?
If the trap is otherwise in good shape and the washers match, washers alone are fine. If the trap is old, stained, cracked, corroded, or the parts do not line up well, a full trap kit is often the easier fix.