Step-by-step fix
Step 1: Make sure a reconnection is the right fix
- Look at the separated joint and confirm the downspout sections are still present and line up with each other.
- Check whether the connector and adjoining sections are only loose or pulled apart, not badly crushed, split, or rusted through.
- Gently test-fit the pieces by hand to see whether they can slide back together without forcing them.
- If the joint came apart after a storm, look up the run for a clog or heavy debris that may have added weight and pulled the connection loose.
If it works: The joint appears reusable, the pieces still match, and the sections can be brought back into alignment.
If it doesn’t: If the connector is missing, deformed, or too damaged to hold, replace it with a matching downspout connector before reconnecting the run.
Stop if:- The downspout is pulling away from the wall because the straps, fasteners, or mounting surface have failed.
- The metal is rusted through or cracked enough that screws will not hold.
- You cannot reach the joint safely from stable ground or a properly placed ladder.
Step 2: Set up the area and remove strain from the joint
- Put on gloves and move anything below the work area that could get wet or be in your way.
- Set the ladder on firm, level ground if you need height to reach the joint comfortably.
- Support the lower downspout section with one hand or rest it so its weight is not hanging on the loose connection.
- Remove any old screws that are bent, stripped, or blocking the pieces from sliding back together.
If it works: The joint is easy to reach, the lower section is supported, and nothing is pulling the connection apart while you work.
If it doesn’t: If the lower section keeps dropping out of place, add temporary support or have someone hold it while you reconnect the joint.
Stop if:- The ladder feels unstable or the ground is too soft or uneven for safe access.
- The wall anchors or straps are loose enough that the whole downspout run shifts when touched.
Step 3: Clean and straighten the connection
- Brush out leaves, grit, and packed debris from both sides of the joint so the connector can seat fully.
- Wipe away mud and check for bent corners, folded seams, or crushed edges that keep the pieces from nesting together.
- Use pliers or gentle hand pressure to straighten minor bends. Trim only small damaged tabs if they block the fit.
- Keep the water-flow direction in mind so the upper section overlaps correctly into the lower section or connector rather than dumping water out at the seam.
If it works: Both sides of the joint are clean, reasonably straight, and ready to slide together in the correct direction.
If it doesn’t: If the edges are too distorted to straighten or the overlap is too short to hold, install a new matching connector.
Stop if:- The downspout sections are split open or too misshapen to reconnect securely.
- You find a hidden clog higher up that is packed solid and likely caused the joint to fail.
Step 4: Reconnect the downspout joint
- Slide the upper and lower sections back together with the connector until the overlap is snug and even on all sides.
- Adjust the alignment so the downspout runs straight and does not twist at the joint.
- Hold the pieces in place and install screws through the sides of the joint where the material is solid.
- Use enough fasteners to keep the connection from rotating or slipping, but avoid overdriving them and deforming the downspout.
If it works: The joint is fully seated, aligned, and held firmly enough that it does not pull apart when you tug it lightly.
If it doesn’t: If the pieces keep slipping apart, remove them and recheck for the wrong connector size, bent edges, or missing support straps above or below the joint.
Stop if:- The screws will not bite because the material is too thin, rusted, or damaged to hold.
- Reconnecting the joint forces the downspout badly out of line, suggesting the run is bent or mounted incorrectly elsewhere.
Step 5: Add support and reduce the chance it separates again
- Check nearby straps or brackets and tighten any loose fasteners so the downspout weight is carried by the wall, not by the joint alone.
- Make sure the extension or lower section is not dragging on the ground or being pushed sideways by soil, mulch, or landscaping.
- If runoff has been backing up, clear visible debris from the top opening or accessible sections so water can move freely.
- Confirm the bottom discharge area is open so water is not pooling and pushing back up the run.
If it works: The reconnected joint is supported, the run is not under side load, and water has a clear path out.
If it doesn’t: If the downspout still sags or shifts, add or repair support hardware before relying on the joint alone.
Stop if:- The gutter above is overflowing heavily or the downspout is clogged beyond what you can safely clear from accessible openings.
Step 6: Test the repair with real water flow
- Run water from a hose into the gutter or upper downspout for several minutes, starting gently and then increasing the flow.
- Watch the repaired joint closely for drips, separation, twisting, or water spilling from the seam.
- Check that water exits at the bottom normally and does not back up into the repaired section.
- After the test, give the joint another light tug to confirm it stayed seated once water weight was on it.
If it works: Water flows through the downspout without leaking or pulling the joint apart, and the connection stays solid after the test.
If it doesn’t: If the joint leaks or shifts, reseat it, tighten the fasteners, and check again for a clog or a mismatched connector size.
Stop if:- Water backs up quickly, indicating a clog or drainage problem elsewhere in the system.
- The joint separates again during the test, which usually means the connector, support, or alignment problem has not been corrected.
Supplies you may need
Repair Riot may earn a commission from qualifying purchases, at no extra cost to you.
FAQ
Do I need a new downspout connector every time a joint comes apart?
No. If the existing connector is still the right size and is not crushed, split, or badly corroded, you can usually reuse it. Replace it when it no longer fits tightly or cannot hold screws.
Which way should the downspout pieces overlap?
Set the joint so water flows down through the overlap instead of catching an exposed edge and leaking out. In general, the upper section should feed into the lower path of water flow.
Can I reconnect a downspout joint without screws?
A friction fit alone often comes apart again, especially during heavy rain or when debris adds weight. Screws help keep the joint from rotating and separating.
Why did my downspout joint come apart in the first place?
Common causes are a clog, loose wall straps, a section dragging on the ground, storm movement, or a connector that was never fully seated. Fixing that root cause helps the repair last.
What if the joint leaks a little after I reconnect it?
First make sure the pieces are fully seated and aligned. Small leaks usually mean the overlap is shallow, the connector is the wrong size, or the seam is distorted enough that the parts are not nesting correctly.