Washer Won't Fill with Hot Water

Quick answer

Check the hot water supply valve is fully open and the water inlet filter is clear. If both are fine, test the hot water inlet valve for power and clogs.

Confirm the symptom

• Washer fills with cold water but not hot
• Water supply to the washer is on for both lines
• Only cold water enters the washer during fill cycle
• No error codes displayed on the washer's control panel
• Washer works normally when using only cold water

Tools and prep

• Screwdriver (flathead and Phillips)
• Adjustable wrench
• Multimeter (for testing electrical components)
• Bucket or towel (to catch water)
• Replacement parts if needed (valve, filter, etc.)
• Turn off power to the washer at the circuit breaker
• Shut off both hot and cold water supply valves

Step-by-step troubleshooting

1. Check Hot Water Supply Valve
   Do: Locate the hot water supply valve behind the washer and ensure it is fully open.
   Observe: Valve is open and water flows freely from the hot water line.
   Means: Valve was closed or partially closed, restricting hot water flow.
   Next: If the valve is open, proceed to the next step.
2. Inspect Water Inlet Filter
   Do: Remove the cold and hot water inlet filters (usually at the back of the washer) and clean them under running water.
   Observe: Filters are free of debris and sediment.
   Means: Clogged filters are preventing hot water from entering the washer.
   Next: If filters are clean, move to the next step.
3. Test Hot Water Inlet Valve
   Do: Use a multimeter to test the hot water inlet valve for continuity. Ensure the power is off before testing.
   Observe: Multimeter shows no continuity or the valve is not receiving power.
   Means: The hot water inlet valve is faulty or not receiving electricity.
   Next: If the valve is faulty, replace it. If it's receiving power, check the wiring.
4. Check Water Inlet Valve Wiring
   Do: Inspect the wiring connections to the hot water inlet valve for looseness or corrosion.
   Observe: Wiring is secure and free from damage or corrosion.
   Means: Loose or corroded wiring is preventing power from reaching the valve.
   Next: If wiring is secure, consider replacing the valve.
5. Verify Water Pressure
   Do: Check the water pressure in the hot water line using a pressure gauge.
   Observe: Water pressure is within the manufacturer's recommended range.
   Means: Low water pressure is preventing proper filling with hot water.
   Next: If pressure is low, check for a partially closed valve or a clogged pipe.
6. Inspect for Blockages in the Water Line
   Do: Disconnect the hot water supply hose from the washer and check for blockages or kinks.
   Observe: Hose is clear and free from kinks or obstructions.
   Means: A blocked or kinked hose is restricting hot water flow.
   Next: Replace the hose if it is damaged or clogged.
7. Test the Water Level Pressure Switch
   Do: Use a multimeter to test the water level pressure switch for continuity.
   Observe: Multimeter shows continuity when the switch is activated.
   Means: A faulty pressure switch is preventing the washer from filling properly.
   Next: If the switch is faulty, replace it.

Common causes

Parts matching

When replacing parts for a washer that won't fill with hot water, ensure compatibility with your washer model.

• Hot water inlet valve (check model number for compatibility)
• Water inlet filter (universal or model-specific)
• Water supply hose (with correct threading and length)
• Water level pressure switch (model-specific)
• Multimeter (for testing electrical components)

Purchase OEM parts or high-quality aftermarket equivalents to ensure proper function and longevity.

When to call a professional

• If the hot water inlet valve is faulty and you're not comfortable replacing it yourself
• If the water pressure issue is due to a main line problem or requires pipe repair
• If the washer still doesn't fill with hot water after replacing all suspected parts
• If you're unsure about electrical testing or wiring repairs
• If the issue is related to a complex plumbing problem or older washer model

FAQ

Related guides

Related searches: washing machine not filling with hot water, hot water not working on washer, washer only fills with cold water, washing machine hot water valve not working, no hot water to washing machine, washer hot water inlet valve replacement, washing machine not getting hot water, hot water supply valve for washer, washer not heating water, washing machine water inlet valve issues