GE Profile Washer Dryer Combo Shaking (Troubleshooting Guide)

On this page

Quick answer
Confirm the symptom
Tools and prep
Step-by-step troubleshooting
Common causes table
Parts matching
When to call a pro
FAQ
Related guides

Quick answer

A GE Profile washer dryer combo shaking during cycles is often due to an unbalanced load or loose components. First, ensure the appliance is level and the feet are adjusted. If shaking continues, check for a damaged suspension system or worn drum bearings.

Confirm the symptom

Shaking occurs during wash or dry cycles
Vibrations are strong enough to move the appliance
Noise increases with shaking
Shaking is not constant but occurs during specific cycles

Tools and prep

Screwdriver set
Towel or padding
Owner's manual
Level
Socket wrench
Turn off power at the circuit breaker
Ensure the area is dry and well-lit

Step-by-step troubleshooting

Check Appliance Level
Do: Use a level to check the washer dryer combo's base.
Observe: Is the unit level side to side and front to back?
Means: An unlevel unit can cause shaking.
Next: Adjust the feet until the unit is level.
Inspect Load Balance
Do: Open the door and redistribute the load evenly.
Observe: Is the load balanced and not overloaded?
Means: Unbalanced loads can cause shaking during spin cycles.
Next: Run a test cycle with a small, balanced load.
Tighten Loose Components
Do: Check and tighten all visible screws and bolts on the unit.
Observe: Are there any loose or missing fasteners?
Means: Loose parts can contribute to shaking and noise.
Next: Secure any loose components and test the unit.
Check Suspension System
Do: Inspect the suspension rods and springs for damage or wear.
Observe: Are the suspension components intact and properly attached?
Means: Damaged suspension can cause excessive movement.
Next: Replace any damaged suspension parts.
Test Drum Bearings
Do: Manually rotate the drum and listen for grinding noises.
Observe: Is there unusual noise or resistance when rotating the drum?
Means: Worn drum bearings can cause shaking and noise.
Next: Replace the drum bearings if necessary.
Verify Proper Installation
Do: Ensure the unit is installed on a stable, flat surface.
Observe: Is the floor solid and free from vibrations?
Means: Improper installation can lead to shaking.
Next: Reinstall or relocate the unit if needed.

Common causes

Cause	Likelihood	Difficulty	Part often needed
Unbalanced Load Uneven weight distribution during spin cycles causes shaking.	Common	Easy	None
Loose or Missing Screws Loose components can vibrate and shake during operation.	Sometimes	Easy	Screws and bolts
Damaged Suspension System Worn or broken suspension parts fail to stabilize the drum.	Sometimes	Medium	Suspension rods or springs
Worn Drum Bearings Worn bearings cause the drum to vibrate and shake.	Rare	Hard	Drum bearings
Unlevel Appliance An unlevel unit can cause uneven drum movement.	Common	Easy	Adjustable feet
Improper Installation Installation on an unstable surface can lead to shaking.	Sometimes	Easy–Medium	None

Parts matching

Common parts needed for a GE Profile washer dryer combo shaking issue include:

Adjustable feet for leveling the unit
Suspension rods or springs for stabilizing the drum
Drum bearings for reducing vibration
Screws and bolts for securing components

Always refer to your owner's manual for part numbers and specifications.

When to call a professional

Shaking persists after checking all components
You hear loud grinding or knocking noises
The unit leaks water while shaking
You are unsure about disassembling internal components
The warranty is still valid and covers repair services

FAQ

Why does my GE Profile washer dryer combo shake only during the spin cycle?

This is often due to an unbalanced load or worn drum bearings. Ensure the load is evenly distributed and check the bearings for wear.

Can I fix a shaking washer dryer combo myself?

Many common issues like unbalanced loads or loose screws can be fixed at home. However, complex issues like damaged suspension or drum bearings may require professional help.

How do I know if the suspension system is damaged?

Inspect the suspension rods and springs for cracks, breaks, or excessive wear. If they appear damaged or do not hold the drum properly, they should be replaced.

Is it normal for the unit to vibrate slightly during operation?

Some vibration is normal, but excessive shaking is not. If the shaking is noticeable or causes the unit to move, it indicates a problem that should be addressed.

What should I do if the unit is level but still shakes?

If the unit is level but still shakes, check the suspension system and drum bearings. These components may be worn or damaged and need replacement.